Skip to content
Aluminum Turned Parts

Turned Parts from Aluminum

CNC turned parts from EN AW-6082, 7075, AlMg3 and other alloys, from one-off parts to large series. We review your drawing and place it with a vetted partner shop. Reply within 24 hours.

In short

Aluminum turned parts are machined on CNC lathes from round bar in alloys 6082, 7075 or AlMg3. Aluminum allows high spindle speeds and therefore short cycle times, and series run economically with a bar feeder. Good turning shops achieve tolerances down to IT6. Strobel Industry places aluminum turned parts made to drawing with vetted partner shops, from 1 piece, anodizing on request. Reply within 24 hours.

RUNDMATERIAL EN AW-6082 CNC-DREHEN 6000 RPM CNC ALU-DREHTEIL ✓ MATERIAL Ø6-250 mm FERTIGTEIL GEPRÜFT
Material

Why Aluminum for Turned Parts?

Aluminum is an ideal material for CNC turned parts: it machines excellently, is light (density approx. 2.7 g/cm³) and, depending on the alloy, reaches strengths above 500 MPa. Good thermal conductivity allows high cutting speeds and short cycle times.

Our partner shops turn aluminum on turn-mill centers and Swiss-type lathes, with live tooling for complete machining in a single setup. We place your part with the shop whose machine fits its diameter, alloy and quantity.

from 1
Piece to Series
6+
Alu Alloys
24h
Reply
IT6
Tolerance Class
Alloys

Aluminum Alloys Overview

Our partner shops process all common aluminum wrought alloys. The choice of alloy depends on mechanical requirements, corrosion resistance and surface treatment.

6082

EN AW-6082-T6

The most widely used structural alloy. Good strength, good machinability, anodizable. Ideal for general mechanical engineering.

7075

EN AW-7075-T6

High-strength aerospace alloy with strengths up to 540 MPa. For highly stressed components in aerospace and motorsport.

5083

EN AW-5083

Seawater-resistant alloy with outstanding corrosion resistance. Ideal for shipbuilding and maritime applications.

2024

EN AW-2024-T4

High-strength alloy with good fatigue resistance. For aerospace, not anodizable.

AlMg3

AlMg3 (5754)

Good corrosion resistance and weldability. For housings, covers and components with lower strength requirements.

AlMgSi1

AlMgSi1 (6082)

Universal standard alloy with good value. Heat-treatable, anodizable, good machinability.

Benefits

Benefits of Aluminum Turned Parts

01

Low Weight

About one third the weight of steel, ideal for lightweight designs in aerospace, automotive and mechanical engineering.

02

Excellent Machinability

High cutting speeds (up to 3,000 m/min) enable short cycle times and cost-effective production even for small quantities.

03

Corrosion Resistant

Natural oxide layer provides corrosion protection. Anodizing can further enhance the protection.

04

Surface Versatility

Anodizing (natural/colored), hard anodizing, chromating, powder coating, glass bead blasting, diverse surface options.

05

Good Thermal Conductivity

Aluminum conducts heat excellently, ideal for heat sinks, heat exchangers and thermally stressed components.

06

Recyclable

Aluminum is 100% recyclable without quality loss. Sustainable material choice for environmentally conscious companies.

Process

Your Alu Part in 5 Steps

01
Schritt 01

Send Inquiry

Send your drawing (STEP, PDF, DXF) with alloy specification, quantity and delivery date.

02
Schritt 02

Review & Placement

Experts from our team check drawing, alloy and tolerances. Within 24 hours we name the right partner shop.

03
Schritt 03

Quote & Approval

The partner shop sends you its quote with unit price and lead time. You approve it directly with the partner.

04
Schritt 04

Production by Partner

The partner shop sources the material and turns your part, with complete machining on live tooling where needed.

05
Schritt 05

Delivery

The partner inspects, packs and delivers directly to you. State documentation such as inspection reports in your inquiry.

Tolerances

Precision for Aluminum Turned Parts

Dimensional Tolerances from IT6

Fits like h6, f7 and H7 are standard. For special requirements, IT5 can be achieved by post-grinding.

Surfaces to Ra 0.4

Fine turning delivers surfaces to Ra 0.4 µm. Polishing or anodizing for even better surface quality.

Runout ≤ 0.01 mm

Tight runout and concentricity tolerances for mating fits and rotating components.

Thread Tolerances 6H/6g

Metric threads, fine threads and special threads to DIN standards. Pipe threads (G, NPT) also available.

In the Network

Typical Machines for Alu Turned Parts

Turn-Mill Center

Turn-Mill Center

For short turned parts in aluminum with cross-holes, flats and threads. Y-axis, live tooling and sub-spindle allow complete machining in one setup.

Use
Short turned parts
Axes
with Y-axis
Tools
live
Swiss-Type Lathe

Swiss-Type Lathe

For slender aluminum parts with small diameters. The guide bushing supports the bar close to the cutting edge, and the bar feeder makes series economical.

Use
Long turned parts
Guidance
Guide bushing
Bar Feeder
for series
Industries

Alu Turned Parts for Your Industry

Mechanical Engineering

Adapters, bushings, spacers and fixtures from 6082-T6.

Automotive

Lightweight turned parts from 7075-T6 for engine and chassis.

Aerospace

High-strength turned parts from 7075 and 2024 to EN/AS standards.

Medical Technology

Anodized aluminum turned parts for device housings and instruments.

Electrical Engineering

Heat sinks, spacer bushings and housing parts with anodized surface.

Renewable Energy

5083 turned parts for wind power, solar mounting systems and inverters.

FAQ

Questions about Aluminum Turned Parts

Q1Which aluminum alloys are possible?

All common wrought alloys: EN AW-6082-T6, 7075-T6, 5083, 2024-T4, AlMg3 and AlMgSi1. Cast alloys on request. The choice of alloy depends on the mechanical requirements, and we advise you on it before placing your inquiry.

Q2What diameters are possible?

Swiss-type lathes handle small diameters from a few millimeters, turn-mill centers with chucks handle larger turned parts. Which diameter is possible for your part depends on the partner shop. State dimensions and quantity in your inquiry and we will check.

Q3Can aluminum turned parts be anodized?

Yes. State anodizing (natural/colored), hard anodizing, chromating or other surface treatments in your inquiry. We place the work with partner shops that supply it themselves or through their finishers.

Q4What is the minimum quantity?

From 1 piece. We place prototypes, small series and large series with partner shops whose machines fit the quantity, for large series with shops running bar feeders.

Q5What does an aluminum turned part cost?

The price depends on alloy, geometry, tolerances, surface and quantity. Aluminum is economical to turn thanks to short cycle times, and the unit price drops significantly for series. The partner shop states the price for your part in its quote.

Q6Is 7075-T6 harder to machine than 6082?

7075-T6 is harder (approx. 150 HB vs. 95 HB for 6082-T6) and requires adapted cutting data. For experienced turning shops both are routine, and the achievable quality is the same. We place work with partner shops that machine both alloys regularly.

Q7Is complete machining (turning + milling) possible?

Yes. Lathes with Y-axis and live tooling machine cross-holes, flats, wrench flats and threads in a single setup. We place work with partner shops running such machines.

Q8What are typical lead times?

The partner shop states the lead time in its quote. It depends on complexity, quantity, material and capacity. If it is urgent, put your target date in the inquiry. We will then look specifically for a shop that can meet it.

Request Alu Turned Part

Send us your drawing with the desired alloy. We review it and get back to you within 24 hours with the right partner shop.

Contact

Ready for the next step?

Send us your drawing. We review the enquiry and pass it on to a suitable, vetted partner shop, free and without obligation .

Strobel Industry Team
✉️ Send Email 📞 +49 (0)172 51 00 715

We will get back to you within 24 hours.